WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

3-in-1 Soil Sensors for Greenhouse Fertigation Control

De herontest November 5th, 2026 7 visualizações

Introduction: Greenhouse fertigation works best when moisture, temperature, and EC come from the same root-zone sample, not from separate probes installed at different times.

An agronomist tuning a greenhouse fertigation program is usually balancing three questions at once: is the substrate drying evenly, is the nutrient solution reaching the intended EC, and are root-zone conditions staying inside the crop's comfort zone. Separate moisture, temperature, and EC probes can answer those questions, but they often sample different spots, different depths, and different moments. The MEC10 3-in-1 sensor puts the three readings in one probe and is described for soil, fertilizer solution, and nutrient solution media. That single-probe approach reduces insertion points and gives the controller a cleaner set of numbers to act on, especially when irrigation events are short and frequent.

Why Greenhouse Fertigation Teams Need Moisture Temperature and EC Data Together

Moisture tells you whether the root zone has enough water. EC tells you how concentrated the nutrient solution is around the roots. Temperature shapes both: it affects root activity, water uptake, and the way EC behaves in the substrate solution. When those three values come from one probe at one depth, the agronomist sees a synchronized snapshot. That matters most during small, frequent irrigation events, where substrate moisture can drop quickly and EC can shift as water is taken up and fertilizer remains behind. A reading that is strong on moisture but based on a separate EC sample from another spot is harder to act on because the two numbers may describe different root-zone conditions. Nutrient solution monitoring gives the other half of the picture. The fertigation tank or mixing line tells you what is being sent to the crop; the root-zone probe tells you what the crop is actually sitting in. In a closed-loop or recirculating system, the gap between those two readings is where many adjustments happen. If solution EC drifts high, the crop may be taking up more water than nutrients; if root-zone EC climbs while moisture falls, salts are concentrating in the substrate. Temperature adds context because warm root-zone conditions can change uptake and EC response. Reading moisture, temperature, and EC together helps the team adjust irrigation duration, dosing ratio, or leaching fraction with more confidence than a single-parameter check. Extension guidance on irrigation scheduling supports the same principle: moisture monitoring is most useful when it is tied to a clear irrigation decision, not treated as a standalone number.

How 3-in-1 Sensors Fit Substrate and Nutrient Solution Monitoring

A 3-in-1 probe fits naturally into two monitoring points in a greenhouse fertigation layout: the root zone and the nutrient solution. The root-zone probe shows what the plant is experiencing. The solution probe shows what the fertigation system is delivering. Running both gives the agronomist a practical loop: adjust the mix, send it, check the root zone, then refine the next irrigation event. MEC10 is described for soil, fertilizer solution, and nutrient solution media, and its fully sealed housing suits wet substrate and solution-side monitoring. The exact placement still follows the crop, substrate, and controller setup.

  • Root-zone substrate monitoring: Place one probe in the active root zone at a representative depth, with good substrate contact. The same reading covers moisture, temperature, and EC, so you avoid three separate insertion points and get one synchronized root-zone snapshot.
  • Nutrient solution and fertilizer solution checks: Use the probe to track EC in the tank, mixing line, or solution sample point. Solution EC helps confirm that the fertilizer recipe is within the intended range before it reaches the crop, while temperature records the solution condition at the same moment.
  • Controller and data logger fit: MEC10 has a fully sealed housing and multiple signal output interface options, with a protection circuit for connection to control equipment. Match the output type, wiring, and power requirement to your controller before installation; Herontest confirms the protocol for your setup.

Installation Conditions That Keep Greenhouse Sensor Data Useful

Depth and contact decide whether the data is useful. A probe pushed into loose substrate near the surface may read drier and warmer than the active root zone, while a probe jammed against a dripper can be washed by fresh nutrient solution and report a locally diluted EC. The practical approach is to install the probe where roots are active, at a depth that represents the crop's main root mass, and in a spot that receives a normal irrigation pattern rather than an edge or a drainage channel. Good contact with the substrate matters because air gaps interrupt the measurement. In coir, rockwool, peat mixes, or soil, the installation method should match the medium and the rooting depth. The controller side is just as important. A sensor that sends a clean signal into a controller with the wrong input type is still a poor installation. Before wiring, match the output interface, wiring order, supply voltage, and whether the controller expects a direct sensor input or a separate transmitter. For greenhouse fertigation, it also helps to record the probe depth, the irrigation zone it serves, and the crop stage so later readings can be compared like for like. Once installed, keep the probe in a stable position and check that the cable is strain-relieved. The fully sealed housing protects the electronics in wet conditions, but the measurement still depends on the substrate, rooting depth, and controller setup. A calibration check at commissioning keeps the readings meaningful for the first irrigation schedule.

Conclusion

For greenhouse fertigation, the value of a 3-in-1 sensor is not just three parameters in one list. It is the ability to compare moisture, temperature, and EC from the same root-zone sample and make a faster, cleaner decision about the next irrigation or dosing step. The MEC10 gives agronomists a single-probe option for substrate and nutrient solution monitoring, with a fully sealed housing and multiple signal output interface options for controller integration. Herontest is a soil moisture temperature EC sensor manufacturer, and we can confirm the interface details your controller needs. When you compare a soil moisture sensor supplier for the project, ask for the same installation and signal details so the comparison is like for like. Send your substrate type, rooting depth, and controller input details, and request a quote with the right probe configuration for your fertigation layout.

FAQ

Q: Are 3-in-1 soil sensors suitable for both greenhouse substrate and nutrient solution monitoring?

A: Yes. The MEC10 is described for soil, fertilizer solution, and nutrient solution media, so one probe design can serve root-zone substrate checks and solution-side EC checks. In practice, many projects use one probe in the root zone and another in the tank or mixing line. Confirm the measurement range and accuracy for each medium with the supplier before ordering.

Q: Where should I install a soil moisture and EC sensor in a fertigation system?

A: Install the root-zone probe in the active root mass at a representative depth, away from the dripper, greenhouse edge, and drainage path. The probe should have firm substrate contact and sit in a zone that receives a normal irrigation pattern. For solution monitoring, place the probe in the tank or a stable sampling point where the nutrient mix is well blended.

Q: How do I confirm the signal output interface before connecting the sensor to my controller?

A: Ask Herontest for the output type, wiring diagram, supply voltage, and connector details for the MEC10 configuration you are considering. Then compare those details with your controller or RTU input. Run a bench check before final installation so the signal, scaling, and wiring are correct. The exact protocol is confirmed for your controller setup.

Sources / References

Measuring Soil Water for Irrigation Scheduling: Monitoring Methods and Devices

Table of Contents

Related Examples

MEC10 3-in-1 Soil Moisture Temperature EC Sensor

Anteriro
IP Protection Test Probe Kits for Certification Lab Benches
Leia mais
Próxima
Selecting Corrosion-Resistant Soil Probes for Saline Land Monitoring
Leia mais